Ti3C2纳米层状材料对废水中Cr（Ⅵ）的光催化去除性能

以Ti₃AlC₂为原料,采用HF刻蚀工艺制备出12种Ti₃C₂纳米层状材料,对其形貌进行了表征,并考察了以其作为光催化剂对废水中Cr（Ⅵ）的处理效果。实验结果表明：HF体积分数为80%、刻蚀时间为48 h时得到的MX-80-48的形貌较好;MX-80-48具有类似石墨烯的二维层状结构,纳米层厚度约20~50 nm,孔径2~10 nm,比表面积14.8 m²/g,在400~700 nm可见光范围内表现出强烈的吸光性;当Cr（Ⅵ）的初始质量浓度为40.00 mg/L、MX-80-48投加量为200 mg/L、pH=2、反应时间4 h（暗反应1 h+光照3 h）时,Cr（Ⅵ）去除率可达100%。     

Challenges for modelling and integrating environmental performances in concept design: the case of an automotive component lightweighting

The objective of this paper is to discuss the main barriers for modelling and integrating the environmental performances in the automotive concept design. Incorporating environmental assessment in the early design phase of a vehicle component is known as an important challenge that car makers need to face in order to develop more sustainable design solutions; in this regard, the Life Cycle Assessment is the most widespread methodology for the environmental assessment and comparison of alternatives. The present work illustrates the combination of such methodology with the traditional design procedure at two different levels of the component design phase, material choice and concept design. In particular, the potential benefits originated by a lightweight solution for the automotive component Throttle Body are evaluated by considering environmental and technical implications at the same level. The case study shows that a multi-disciplinary approach for design effectively allows the integration of the environmental issue in the company’s established procedures. However, interpretation of results is still a challenging aspect due to the inevitable contradicting elements which should not discourage to develop comprehensive sustainability assessment within the early design stage.     

企业安全管理体系标准模式的比较研究

采用对比分析法和实证分析法,对当前国内外流行的企业安全管理体系标准模式及其评价方法进行比较研究,旨在把握诸多标准模式的原则、路径、结构、方法和共性特征及其可以发挥的具体优点,将研究的标准模式的评价方法归纳为两大类即体系认证审核法和综合考评打分法,并对两类评价方法的优缺点进行剖析。体系认证审核法的优点是过程方法、符合性及抽样,考评打分法则提供了安全绩效准则。对吸收融合两类评价方法的优点形成综合性评价方法的途径和方式进行了探讨,为企业建立有效、适用的安全管理体系提供了依据。     

我国消防标准体系分析

为明确我国消防标准体系发展的方向和重点,分别从消防标准的数量、标龄、类型、属性和采标情况等5个方面对我国消防标准体系进行分析,并与国际标准化组织、欧盟标准化委员会和美国的消防标准体系进行了比较。研究结果表明:我国消防标准体系整体适用性在不断增强;需制定周期性标准复审计划;消防基础试验类和管理类标准应成为下一步消防标准制修订的重点;消防强制性标准所占比例有待进一步下调;需建立国际标准动态跟踪机制,同时应注重将我国先进的消防标准转化为国际标准。     

Effects of bed materials on the performance of an anaerobic sequencing batch biofilm reactor treating domestic sewage

The objective of this study was to determine the best performance of an anaerobic sequencing batch biofilm reactor (AnSBBR) based on the use of four different bed materials as support for biomass immobilization. The bed materials utilized were polyurethane foam (PU), vegetal carbon (VC), synthetic pumice (SP), and recycled low-density polyethylene (PE). The AnSBBR, with a total volume of 7.2L, was operated in 8-h batch cycles over 10 months, and fed with domestic sewage with an average influent chemical oxygen demand (COD) of 358+/-110mg/L. The average effluent COD values were 121+/-31, 208+/-54, 233+/-52, and 227+/-51mg/L, for PU, VC, SP, and PE, respectively. A modified first-order kinetic model was adjusted to temporal profiles of COD during a batch cycle, and the apparent kinetic constants were 0.52+/-0.05, 0.37+/-0.05, 0.80+/-0.04, and 0.30+/-0.02h(-1) for PU, VC, SP, and PE, respectively. Specific substrate utilization rates of 1.08, 0.11, and 0.86mg COD/mgVS day were obtained for PU, VC, and PE, respectively. Although SP yielded the highest kinetic coefficient, PU was considered the best support, since SP presented loss of chemical constituents during the reactor's operational phase. In addition, findings on the microbial community were associated with the reactor's performance data. Although PE did not show a satisfactory performance, an interesting microbial diversity was found on its surface. Based on the morphology and denaturing gradient gel electrophoresis (DGGE) results, PE showed the best capacity for promoting the attachment of methanogenic organisms, and is therefore a material that merits further analysis. PU was considered the most suitable material showing the best performance in terms of efficiency of solids and COD removal.     

对导热炉大气污染物排放执行标准的探讨

目前，相关环境标准中均未明确制定关于导热炉大气污染物的排放内容。因此，对于导热炉的大气污染排放，各环境管理及监测部门均没有统一的执行标准。本文从导热炉工作原理、污染物排放特点等方面进行了分析，对其执行标准提出了个人的观点。     

石期河流域地下水化学特征及物质来源分析

为明确典型岩溶溶丘洼(谷)地区域地下水化学特征及其成因,以石期河流域为研究对象,运用Gibbs图、Piper图、端元分析及离子比例系数等方法,对地下水水化学特征及物质来源进行了定性和定量分析.结果表明,研究区内地下水pH值介于6.06～8.07之间,Ca~(2+)、 Mg~(2+)和HCO~-_3是地下水中的主要离子,其质量浓度范围分别为2.61～108.7、 0.54～27.61和8.1～370.74mg·L~(-1),符合岩溶水高钙弱碱性特征;地下水物质成分中, Ca~(2+)和Mg~(2+)主要受到碳酸参与的灰岩和白云岩风化作用的控制, Na~+主要来源于硅酸盐岩的溶解,同时, Ca~(2+)和Na~+在地下水流动过程中进行阳离子交替吸附作用; K~+、 Cl~-和NO~-_3主要受到农业化肥施放和生活废水排放的影响.此外,大气降水作为该区域地下水的主要补给来源,对当地地下水化学特征和物质来源也有一定的影响.     

磁性氧化石墨处理乳化含油废水及磁致增强效应

以高铁酸钾为氧化剂,基于改进Hummers法制备了新型磁性氧化石墨材料,在SEM、FTIR、氮气吸脱附和表面接触角表征基础上,探究了该材料处理乳化含油废水的效果及磁致增强效应.结果表明：相较于石墨,磁性氧化石墨比表面积增大,表面有卷曲结构并负载着Fe₃O₄颗粒,具有含氧官能团,存在疏水性较强的微观孔隙结构.在外加磁场条件下,磁性氧化石墨团聚,形成疏水性宏观孔隙结构,利于乳化油滴的吸附和附着.磁性氧化石墨处理乳化含油废水的能力远好于石墨与粉末活性炭,且处理效率与磁场强度成正相关,COD去除率可达95%以上.使用后的磁性氧化石墨进行溶剂萃取或热处理,可以循环使用.磁性氧化石墨经过4次循环使用,热再生效率为92%,溶剂萃取再生效率为86%.以上研究为乳化含油废水的处理提供了一种有效的方法.     

中国沿海省市海洋生态补偿效率评价

本文运用考虑非期望产出的超效率SBM模型、DEA-Malmquist指数模型、Tobit模型和标准差椭圆模型,对2006-2016年中国11个沿海省市的海洋生态补偿效率开展测度和分析,结果显示：2006~2016年中国总体海洋生态补偿效率平均值为0.633,处于中等效率水平,随时间呈“下降-上升-稳定”的趋势;海洋生态技术进步依旧是海洋生态补偿过程中全要素生产率的重要驱动力,但面临一定的技术效率损失;海洋第三产业比重对海洋生态补偿效率值有正向的显著影响,城市化率、进出口总额占比和海洋灾害直接经济损失对海洋生态补偿效率存在显著的负向影响;海洋生态补偿效率的空间聚集性增强,区域不平衡性有所收敛,空间分布格局基本保持稳定.     

中国乘用车塑料的动态物质流分析

结合行业信息并基于动态物质流模型,本文对1950~2050年间中国乘用车塑料流量与存量进行了历史测算与情景分析.历史测算表明：1950~2018年国内乘用车行业累计消耗了以聚丙烯（PP）、聚氨酯（PU）等为主的塑料3278万t,产生了337万t塑料废弃物;报废汽车拆解后的车用废塑料仅28%得到回收利用.针对未来情况,本文设计了乘用车保有量、单车塑料使用量两大关键因素下的不同情景组合.结果显示车用塑料存量及废塑料产生量将大幅增长,到2050年存量将达到0.7~2.7亿t,废塑料产生量将达到500~1600万t,汽车拆解和塑料再生等相关行业对此应充分关注.到2050年车用废塑料回收率若能提升至80%,将减少376万t/a的车用废塑料填埋或焚烧,显著减少环境风险.